Technical Support

Coolant Management

Coolant Management Assistance Guide PDF

  • Concise easy-to-understand guide to coolant use and maintenance
  • Aid to troubleshooting coolant maintenance problems

Coolant Maintenance Chart PDF

  • Use this chart to track coolant condition as well as coolant and water additions.
  • Use a separate sheet for each machine.

Coolant Troubleshooting

We have compiled a guide for troubleshooting the following scenarios that may arise. Select the ones that relate to your situation the most to see the possible solutions.

Corrosion
  • Too Weak Concentration: Adjust and maintain concentration as recommended by coolant manufacturer.
  • Poor Water Quality/Corrosive Ion Buildup from Water: Use better quality water such as deionized, reverse osmosis or softened water.
  • High Temperature/Humidity: Reduce temperature and humidity and/or use a supplementary rust preventative.
  • Contamination: Identify and eliminate contaminants that promote corrosion, such as heat treating salts.
  • Corrosive Atmosphere: Identify and vent corrosive fumes out of problem area. Could be from heat treat or propane forklift truck exhaust.
  • Part Handling/Storage: Use clean, plastic dividers to allow parts to dry and remain separate. For extended storage, use a supplementary rust preventative
Poor Tool Life
  • Too Weak Concentration: Adjust and maintain concentration as recommended by coolant manufacturer.
  • Water Quality: Hard water (greater than 200 ppm Total Hardness) can promote mix instability in metalworking fluids and lead to loss of tool or wheel life.
  • Changes: Verify that no changes have been made to the coolant, tooling or material you are working with.
  • Contamination: Identify and eliminate or minimize contaminants that promote loss of tool or wheel life, such as high levels of hydraulic or way oils, floor cleaners or other coolants.
Foam
  • Too Strong Concentrate: Adjust and maintain concentration as recommended by coolant manufacturer.
  • Type of Operation: Some operations, such as high-speed milling or surface grinding, can promote foam. Work with your coolant supplier to implement the product properly suited for your operation.
  • Contamination: Look upstream from operation. What chemical or lubricant has been in contact with the part, and how does this impact foam?
  • Water Quality: Soft water (less than 100 ppm Total Hardness) can promote foam in some metalworking coolants.
  • Coolant Level Low: Keep the sump full in order to maximize fluid retention time in sump and allow the air to come out of the mix.
  • Mechanical Problems: Check the fluid delivery, filtration system, and fluid return systems for mechanical problems and repair them. Kinks in the hoses or small pinholes may allow air to be pulled into the system.
Coolant Instability
  • Water Quality: Hard water (greater than 200 ppm Total Hardness) can promote an unstable mixture. Technology exists to prevent this, particularly in synthetic products.
  • Contamination: Identify and eliminate or minimize contaminants that promote coolant instability. These may include tramp oils, way lubricants or chemicals from a previous process.
  • Concentration: Adjust and maintain concentration as recommended by coolant manufacturer
Tackiness/ Stickiness/ Gooeyness
  • Quality of Water: Hard water (greater than 200 ppm Total Hardness) can create tackiness in certain coolants. Your coolant supplier can provide coolants with blended additives that naturally soften the water.
  • Delivery: Some machining centers may have “blind” areas where coolant in not in continous contact. With heat and time the water will evaporate, leaving a film that will cause chips to cling. A daily flush of the area with coolant will reduce this problem.
  • Contamination: Identify and eliminate or minimize contaminants that promote coolant instability. These may include tramp oils, way lubricants or chemicals from a previous process.
Poor Surface Finish
  • Concentration: Adjust and maintain concentration as recommended by manufacturer.
  • Coolant Instability: When coolants become unstable (see “Coolant Instability” below), the additives can be depleted and lead to more rapid tool wear. This is common for older soluble oil formulations. Newer synthetic formulations do not have this problem.
  • Changes: Verify that no changes have been made to the coolant, tooling or material you are working with.
Rancidity
  • Concentration: Adjust and maintain concentration as recommended by coolant manufacturer.
  • Circulation: Keep it moving. Circulating the tank will assist with sump life.
  • Tramp Oil: Tramp oil can promote microbial growth, especially in soluble oil formulations. Implement preventative maintenance practices to minimize tramp oil. This will improve coolant life and minimize waste.
  • Contamination: If adding water manually, use clean buckets. Minimize tramp oil and use oil skimmers.
  • Micro-Biological Activity: If concentration and other factors are not the cause, then the use of a tank-side biocide may be necessary. Advancements in coolant technology have minimized this. If your coolant requires this, contact the manufacturer. A machine cleaner may be necessary to eliminate bacteria or fungus.

Sustainability Program

 

Monroe Fluid Technology is taking steps to reduce our carbon footprint and enhance our Sustainability Program. You will notice these changes soon as we introduce the use of White Steel Drums and Reconditioned drums for many of our products.

Technical Services

 

TELE-CONSULTING- Lab personnel are available to answer questions regarding selection, application, safety, handling, and maintenance of all MONROE FLUID TECHNOLOGY products, including troubleshooting, assistance, and cross-referencing of competitive products.

COOLANT ANALYSIS-MONROE PRODUCTS- Monroe provides sample bottles, mailers, and preprinted return labels for routine analysis of in-use coolant samples at no charge. Analyses include biological activity, concentration, contaminant level, and pH, among others. Full reports with any recommended action are promptly forwarded to the customer.

Professional Associations

Independent Lubricant Manufacturers Association (ILMA)

The Independent Lubricant Manufacturers Association has been the voice of member companies since 1948.  The members produce more than a quarter of the US supply of automotive fluids and lubricants, and three quarters of the the metalworking fluids used in the country.  ILMA serves as the industry voice to government and regulatory bodies, and serves an integral role to its membership through education and training opportunities. (View Ilma Membership Certificate)

Society for Tribology and Lubrication Engineering (STLE)

Monroe Fluid Technology is a member of the Society for Tribology and Lubrication Engineering (STLE). STLE is a professional technical society providing a selection of robust resources in technical research, education and professional development delivered through programming, courses, events and periodicals on topics most important to you: safety, energy usage, maintenance, natural resources, wear and productivity.

Dust Control

1095 Evergreen Circle, Suite 200
The Woodlands, Tx 77080

Phone: 844-8 NO DUST (66-3870)
Email: defeatdust@dura-crust.com
Website: www.dura-crust.com